Find The Best Paver Sealer

What are the best paver sealer in the market? Yes, they are tons and that often makes people confused. But based on real verified user’s feedback and reviews and best selling list of different marketplaces we have listed here top 10 paver sealer we listed and compiled reviews from verified purchase owners.

So, if you like to have one paver sealer hope the following feedback from real users will help you a lot.

Note that we compiled here only five star ratings and reviews.

Best paver sealer Comparison Table

Best Overall
Low Gloss Patio Paver Sealer, 1 gal - Clear Water-Based Sealant for Natural Stone Surfaces
Low Gloss Patio Paver Sealer, 1 gal - Clear Water-Based Sealant for Natural Stone Surfaces
$44.99
Editor's Choice
Glaze
Glaze 'N Seal Paver Sealer, 5 Gallon (154)
$199.99
Nice Pick
1 Gal. DOMINATOR LG+ Clear Acrylic Sealer | Low Gloss Paver Sealer | Wet Look, Color Enhancing | Professional Grade | Concrete Pavers and Decorative Concrete | Fast Dry | Driveway, Patio and Walkways
1 Gal. DOMINATOR LG+ Clear Acrylic Sealer | Low Gloss Paver Sealer | Wet Look, Color Enhancing | Professional Grade | Concrete Pavers and Decorative Concrete | Fast Dry | Driveway, Patio and Walkways
$79

Top 10 Best Paver Sealer

paver sealer
Here are the top paver sealer we picked, check their features.

1. Low Gloss Patio Paver Sealer, 1 gal – Clear Water-Based Sealant for Natural Stone Surfaces

Low Gloss Patio Paver Sealer, 1 gal - Clear Water-Based Sealant for Natural Stone Surfaces

  • Invisible Waterproofing Protection – Milky white in appearance when first applied, and dries clear
  • Non-Yellowing, Clear, Water-Based, VOC Compliant Acrylic Sealer – Low Odor and Easy Cleanup with Soap & Water
  • Helps Prevent Color Loss on Patio Stone Pavers
  • Ready to Use – No Mixing Required – Easy to Apply with a Pump Up Sprayer
  • Provides a Low-Gloss Finish to Patio Paver Stones (Does not leave a high gloss finish on your paver stones but rather, a rich angular sheen that protects your pavers from fading and hardens, or “stabilizes” the joint sand. The amount of sheen will vary, based on the porosity of the pavers).

Reviews from Real Users

Amazon Customer

I am extremely pleased with the results of this product. Our 7-year old 10x10 paver patio has never been sealed and was looking sad with lots of weeds. After killing off the weeds, I power washed and replaced the sand with an expensive polymeric sand. The sand washed away during rains and never fully hardened. I purchased this sealer and was immediately pleased with the results. I sprayed only since I didn't have an outdoor brush. The bottle covered 2 coats and the sand is now rock hard. Many people mentioned that it does not leave a wet look. It does not does leave a slight sheen, just as described in the description. Wish I would have found this product 7 years ago!

Gary Larson

Product applied easily with a garden sprayer. It has held up well through the full Summer season. I like the shine and also the fact that it did not make the surface slippery.

David E. Smith

I just did the application a few days ago, so I can't attest to durability. I used a roller to apply it and it went on easily. I used a paintbrush attached to a stick to smooth out the excess in deep crevices. The second coat went on even easier than the first. The result was a great look. I am pleased.

2. 5 GAL Armor AR350 Solvent Based Acrylic Wet Look Concrete Sealer and Paver Sealer

5 GAL Armor AR350 Solvent Based Acrylic Wet Look Concrete Sealer and Paver Sealer

  • The Armor AR350 is a breathable, non-yellowing solvent based acrylic that will darken concrete and pavers to make them look wet, and provide a long lasting, durable low gloss finish.
  • The Armor AR350 is manufactured in the US and made from non-recycled resins.
  • The Armor AR350 is self-priming and can be applied to unsealed concrete and paver surfaces, as well as surfaces previously sealed with a solvent based acrylic sealer.
  • The Armor AR350 will help to reduce damage and deterioration caused by surface abrasion such as dustring, cracking, spalling, and pitting.
  • The Armor AR350 can last up to 1-3 years on exterior surfaces and up to 3-7 years on interior surfaces before the need for a recoat.

Reviews from Real Users

Jreview

We had Unilock pavers installed about 2 years ago, and while we loved the style of our patio, some of the polymeric sand always seemed to wash out and made the pavers look dirty and hazy which was very frustrating. We were constantly trying to clean the pavers, only to have the same thing happen over and over again. We were to the point that we wished we had built a deck instead of the patio.

So we decided to try sealing our pavers in the hope of keeping the polymeric sand in place better and keeping the haze and dirt from staining the pavers. We applied 2 coats of this sealer to our approx. 450 sq. ft. patio (so we covered about 900 sq. ft. total) and wound up with approx. 1 gallon left from the 5 gallon drum that we ordered. We are very pleased with the results! We sealed the patio about 3 weeks ago, and it looks clean and beautiful. We have had multiple heavy rains and the patio finally has been able to stay clean!! After 2 years of frustration, we now have a patio that we are able to enjoy.

When I was looking for a sealer, I was a little confused in reading the reviews. Some people said they got a nice wet look and other folks complained that the finish wasn't shiny. After seeing the results on our pavers, I understand why people had different opinions on the finish. If you have a dense, smooth paver or surface, you will get a fairly glossy result. If your paver or surface is more rough or textured (like a sandstone finish), you will see a very light sheen (not a wet, glossy look). On our patio, the main pavers are Unilock Copthorne pavers which are very dense and more smooth, so those came out with more of a wet, glossy shine. Our patio is trimmed with Brussels block pavers which are more textured and resulted in a very light soft sheen - not a glossy look. So your final appearance will all depend on what type of surface you are starting with.

Some tips - we applied the product with an inexpensive pump sprayer and then rolled it out with a roller on a pole. We probably spent about an hour and a half or 2 hours to do each individual coat on a 450 sq. ft patio (including getting the equipment ready). My husband sprayed, and I used the roller - great if you have 2 people. Sometimes the fluffy nap on the roller was lightly shredding off and sticking to the patio like fine strings of cotton candy. I thought it was the roller, but after switching the roller we had the same issue. We discovered that we either weren't applying enough sealer or we were trying to do too large an area and the sealer was drying too quickly and pulling nap off the roller. Once we applied a little more product and worked on a smaller area we did not have a problem. My husband would spray about a 6ft by 6ft area and would wait till I was almost done rolling before moving to the next area. That worked well for us - it was very windy the day we applied the product and I think it was drying very quickly. I found it was helpful to roll at about a 45 degree angle quickly and then I would finish with fast straight strokes before starting the next area. Rolling on the diagonal first before the straight strokes helped since our pavers were laid in a herringbone pattern.

I would definitely recommend using a funnel if you are pouring the product into a sprayer. We did that the first day and were able to properly clean and reuse our sprayer. When we applied the second coat the next day, we decided to skip the funnel and poured directly into the sprayer. Everything was great until we tried to clean the sprayer and could not unscrew the top. We had gotten sealant on the threads of the sprayer and wound up having to throw the sprayer out. If we had used the funnel, I'm sure we would have been able to save the sprayer.

We did not use any non-slip additives, and we feel that out patio is fine, although I would say it is slightly more slippery that the unsealed pavers. If we had an even smoother paver or we were applying this to a heavily used sidewalk, we might consider adding that additive.

We followed all the application instructions and had no issues with any hazing or clouding on the pavers. Note that you need about 24 hours of dry weather before applying and then approximately another 24 dry hours afterwards to help ensure you get good lasting results. The hardest part of the project was waiting for the proper weather conditions since we were anxious to get started but there was too much possible rain in the forecast. We were patient, and were rewarded with great results!

I attached a few pictures, and in one photo I added a couple of the original pavers so you can see the difference in the color and shine. The sealer definitely darkened the pavers, and I feel that they look a little more brown than their original color.

I highly recommend this Foundation Armor sealer!

globetrotter

I can't rave enough about this product. I have an exterior patio to our house. It's a fairly large patio and has flagstone natural stone throughout. Our house is about 13 years old and the stone was all dull and the stone has lightened considerably. It always looks dirty when dry but when wet looks really great. That's when I started researching online products that will darken stone and seal it and give it a wet look. I saw the great reviews on Amazon as well as saw some videos on YouTube.

I was still a bit skeptical as the product isn't cheap at $225+ plus all the supplies and also the time. But I figured it would be worth the investment to try it. First step is I power washed the entire flooring with a SunJoe power washer (excellent that I also purchased on Amazon). I let it completely dry 2 days and then I got a sprayer and sprayed down the Armor AR350 and then took a roller and evenly distributed the solvent.

Immediately I saw it darken the stone and gave it a wet look. I got tempted to just use one coat as it looked great with one coat. But I followed the instructions and I put down another coat after 24 hours. I'm glad I put down a 2nd coat as it looks better with another coat and I'm sure it will last at least another year with another coat.

It totally waterproofed the stone and water beads up. I think it will be much easier to clean the patio as dirt can't easily stick to the stone now. I did an entry way as well as the entire outdoor patio. It's about 1,500 sq. feet and I just had enough with the 5 gallons to do 2 coats.

My wife was skeptical before I started but she is so happy that I completed the project. There is a bigger satisfaction because I did it myself. This is a really easy DIY project and well worth it. I posted some before and after photos.

Macboy

I have a 30x20 stamped concrete patio that is 14 years old. I took the cheap route and re-sealed it 4 years ago with Behr concrete sealer (do not use this stuff) from Home Depot and I subsequently had a white haze on my patio pavers that was very difficult to remove. Multiple cans of epoxy stripper and 2 days of power washing is what it took to remove this old sealant. Ok, now I was determined to buy a quality sealant to bring my patio back to life and I ordered this stuff. All I can say is it arrived within 2 days of ordering and it was the best money I spent on a DIY project. This sealant (5 gal bucket) was enough to do two coats and my patio looks absolutely great, like brand new. The design in the stamped concrete pavers really stands out and the low gloss sheen that gives the patio a constant wet look is exactly what I wanted in a sealant. I highly recommend this product and will purchase again when the time comes to re-seal in 3-5 years. I also ordered some slip resistant additive that you easily pour into the bucket of sealant and shake it up pretty good. Application tips can be found on youtube. I installed with a 3/4 inch thick roller and cut in the edges of patio with a small brush.

3. Glaze ‘N Seal Paver Sealer, 5 Gallon (154)

Glaze

  • Long-lasting protection against surface stains and color fading
  • Easy application process with professional sealing results
  • Enhances natural appearance of masonry surfaces
  • Low VOC water based formula qualifies for LEED points
  • Top notch stain resistance fights oil, grease, rust, mildew and salty white stains

Reviews from Real Users

Amazon Customer

Had weeds and gaps growing through an old paver patio. Rebuilt the patio complete with weed barrier and re-leveling of the sunken pavers. Used polymeric sand to grout the pavers together but it never hardened up. In between the pavers was pretty much a sandbox. Took a leap and of faith on this stuff in a small section just in case it stained the pavers at 8pm. Next day at 6pm I came out and it was hard and the sand was hard as a rock! No staining of the pavers either. Only draw back is it’s a bit pricey, but I’m confident this will last for years to come as it relates to weeds and moss. Polymeric sand was from Home Depot as info.

Pape

I’ve wasted hundreds on other sealers that as soon as my brand new pavers got wet most of the sand between washed away and have actually stained my pavers.
This product sealed the sand and did not wash away or discolor my pavers. I plan on basically starting over by cleaning the pavers and have purchased more of the Glaze ‘N Seal. Great product!

Gorilla

I was wanting something that would harden sand between my pavers. This product did exactly what I was looking for. It won't be a permanent solution but I am happy with the results.

4. 1 Gal. DOMINATOR LG+ Clear Acrylic Sealer | Low Gloss Paver Sealer | Wet Look, Color Enhancing | Professional Grade | Concrete Pavers and Decorativ

1 Gal. DOMINATOR LG+ Clear Acrylic Sealer | Low Gloss Paver Sealer | Wet Look, Color Enhancing | Professional Grade | Concrete Pavers and Decorative Concrete | Fast Dry | Driveway, Patio and Walkways

  • COLD WEATHER WARNING: Do not apply if surface temperature is expected to be below 50° for 48 hours before & after application. ENHANCE the life and beauty of your surface (wet look) and a low gloss finish for 2-4 years before the need to reseal (depending on your environment).
  • Protects against oil stains and other spills while providing the ultimate weather resistance on surfaces including concrete pavers and decorative concrete. Not intended for stone or clay.
  • Great coverage rate: 250-400 square feet per gallon, per coat. You will save money and time by reducing maintenance when you seal with DOMINATOR LG+.
  • Breathe easy with DOMINATOR LG+ concrete sealer’s water-based formula. No harsh odors and low VOCs (Volatile Organic Compounds) makes application pleasant and easy.
  • Easy spray on application using our Quick Start guide (included in every purchase) and How To videos. DOMINATOR LG+ has an incredibly fast dry time between coats making it an easy one-day project, unlike some competitors.

Reviews from Real Users

BR in Paradise

I wanted a "wet" look - wife did not. The "low gloss" product made us both happy. Picture 1 shows right side completed vs. left side not. Hard to see a major difference. 2nd photo shows the final finish much different light. . Did it darken the pavers? Perhaps a little - but no one would notice. Is there a "wet" look - not really - if you want a truly wet look you may want to consider the high gloss product. I used a sprayer in 3 foot by 3 foot sections and then rolled it out to make it uniform. As it was sunny and we are in Florida - in two hours I added the second coat. That went on a lot easier then the first coat due to different absorption. I did a very small area test before doing the whole patio. There is no doubt that this product will work - a rain will bead. I did a lot of internet research before selecting this product. The reviews sold me. Can't wait for the first rain to see the result. I hope it lasts a long time because moving all the plants and furniture was a PIA!

RickyN29

I could not be happier. This went on super easy, is very forgiving, and the difference is amazing. Somewhat hard to tell in my picture but it really brought out the colors, gave a nice wet look but with a matte finish, and I can tell this will protect well. Also locked in the sand quite nicely. I oversprayed on decking, pots, rocks and artificial grass and it caused no problems at all.

I highly highly recommend!

CW1979

Love this sealer and the finished look. Applied two coats to my brick pavers using a $10 garden sprayer. Very easy to apply, took less than an hour to cover 1500sqft. It is very sticky and hard to remove from hands, wear gloves!
Most areas dried quickly with no issues. A few spots remained white and took up to a week to cure. White spots did appear after rain for the first month but stopped appearing when wet after a month or so. We have a outdoor stall type bathroom, it has yet to fully cure in that area and remains sticky, in hindsight I would have only applied one coat to this area as it didn’t need as much protection. Some ants have been able to make their way through as well as a few weeds, however not enough to matter. Sand lines can hold dirt after rains but they wash off easily with a garden hose.
Overall a great product!

5. Gloss, Wet Look Patio Paver Sealer, 1 gal – Clear Water-Based Sealant for Natural Stone Surfaces

Gloss, Wet Look Patio Paver Sealer, 1 gal - Clear Water-Based Sealant for Natural Stone Surfaces

  • Clear, Waterproof Protection With a Gloss, Wet-Look – Gives Pavers a Slightly Darker, Enhanced Color
  • Low Odor, Water-Based, VOC Compliant Acrylic Sealer – Easily Cleans Up with Soap & Water (an industrial orange hand cleaner such as Gojo, or similar can be used for easier cleanup)
  • UV Protective Coating Helps Prevent Color Loss & Hardens Joint Sand to Lock it in Place
  • Ready to Use – No Mixing Required – Easy to Apply with a Pump Up Garden Sprayer
  • Provides a Gloss Finish to Patio Paver Stones (sheen varies based on the surface porosity)

Reviews from Real Users

Suzanne Rogers

Love love this stuff! Side by side shows the difference three coats gave it the shine I wanted vast improvement!

RCC

I used this to seal my river rock pool deck and it looks even better than the sealer I bought at the local paint store which I used a few years ago. The prices were about the same but this product is easier to apply as I used a sprayer instead of a long handled roller and did the entire deck in about half the time. The pool deck came out great and this sealant shines in the sunlight and is water resistant while not being slippery. I am very pleased with this product and would highly recommend it. I would use this product again without any hesitation.

Amazon Customer

Update: still looks wonderful!!!

Easy to use. Used for patio pavers and applied very nice and easy. I applied with a paint roller. Dried faster than most products. Not sure how it holds up but my pavers looked so dull, old, dusty and this made them look bright and new right quick.

6. 1 Gal. DOMINATOR SG+ Clear Acrylic Sealer | High Gloss Paver Sealer | Wet Look, Color Enhancing | Professional Grade | Concrete Pavers and Decorati

1 Gal. DOMINATOR SG+ Clear Acrylic Sealer | High Gloss Paver Sealer | Wet Look, Color Enhancing | Professional Grade | Concrete Pavers and Decorative Concrete | Fast Dry | Driveway, Patio and Walkways

  • COLD WEATHER WARNING: Do not apply if surface temperature is expected to be below 50° for 48 hours before & after application. ENHANCE the life and beauty of your surface (wet look) and a high gloss finish for 2-4 years before the need to reseal (depending on your environment).
  • PROTECTS against oil stains and other spills while providing the ultimate weather resistance on surfaces including concrete pavers and decorative concrete. NOT intended for stone or clay.
  • GREAT COVERAGE RATE: 250-400 square feet per gallon, per coat. You will save money and time by reducing maintenance when you seal with DOMINATOR SG+.
  • Breathe easy with DOMINATOR SG+ concrete sealer’s water-based formula. No harsh odors and low VOCs (Volatile Organic Compounds) make’s application pleasant and easy.
  • EASY spray on application using our Quick Start guide and How To videos. DOMINATOR SG+ has an incredibly fast dry time between coats (45 min.) making it an easy one-day project, unlike some competitors.

Reviews from Real Users

Kathleen

This is an update to a previous review.... I received the wrong product twice. LG not SG. For those who are confused, that's low gloss vs semi gloss. Amazon had told me that black diamond fulfilled my order. This was not true. After speaking with the companies customer service, I can't say enough about them. Not only did they make it right, they got it to me on time when Amazon could not. More companies should act like and treat their customers like BD coatings.
Let me clarify some of the bad reviews you may be reading. This product is awesome! First, it goes on so easy with any power sprayer, i used one from home Depot for $15. It's best back rolled with a corregated foam roller. It has no odor, necessity for my pregnant wife. Second, it can take longer to dry IF the substrate you pressure washed takes longer to dry/not in the sun, BUT, it does dry and looks fantastic. For example, my screened patio (pic) in Florida that doesn't see sun took longer to dry than the pool patio. Still able to walk in it in a few hours, just tacky a few days where patio was not 1 day later. Next, the product goes on white and dries clear. I love this because you can see where you're going and how thick you laid it down. If it rains a few hours after you laid it down, it may get white again. Don't freak out, this is only temporary and dries clear. It won't do this every time it rains, just if it rains immediately after application. The rain did not effect the color or water beading on my bricks. Finally, know your bricks. This product doesn't "peel like a snake" as another reviewer wrote. He probably neglected to remove/didn't know he had a solvent based sealer on his stone. The benefit of using water based sealers are no odor, easy clean up and easy application. If you have previously used a solvent based sealer you must stick with that or remove it with a stripper. They say solvent based sealers get the stone darker, bead water better and have a better gloss, well that's BS, look at my pics. I got all that with water based SG+! I can't see why anyone would go through the hassle of solvent based sealers when this product works so much better.

tompat

We had samples of a water based polyurethane and this Black Diamond Acrylic. Applied 2 coats of each to 2 Belgarde New Holland concrete pavers. Eight individuals reviewed each of the sealed pavers. Six of the eight chose the Black Diamond Acrylic stating it had a wetter deeper color. We had 1900 sq ft of new pavers installed and sealed same with the Black Diamond Acrylic. The coverage averaged 308 sg. ft /gallon. The paver colors were enhanced and the gloss is obvious without any slipperiness. Getting compliments from our neighbors. Very pleased with the result.

Brian B.

This product provided an unbelievably beautiful showroom "wet look" gloss to our pavers. I'm thrilled with the end result, and I have a new sense of pride in our back yard. That said, here are some caveats because the prep work - by no fault of the company - is *brutal* and painstaking:

1) Wait for a week's period when the temperature is between 70 and 85 degrees daily, with near zero humidity - even at night. Clean one spare paver with water and a scrub brush, or pick an existing paver in a more hidden section of your property and do the same. Order the 4oz tester, which comes in a spritz bottle. Once the paver has been dry for 48-72 hours, spritz the single paver until the surface is milky white, and wet - stop just before it gets wet enough to run. Do NOT sponge or surface roll; splatter or dots are fine. Once you've sprayed, you may notice milky spots, but DO NOTHING. It looks like you sprayed it with curdled milk, and you'll be thinking "This can't possibly be right!" It is. Leave it alone.
2) The next day, with temperatures between 70 and 85 degrees, and near zero humidity, spritz the paver again for a second coat. Remember, your goal is to slowly spritz enough liquid that it's covered, stopping just a bare second before it gets wet enough to run. Again, it will look like garbage. Now forget about it. Let it sit out in the sun for a week or so. No, really. Walk away and forget it exists.
3) Now, after a full week, go see what it looks and feels like. The surface should be rock hard, much smoother to the touch, and have a nice glossy finish with a touch of shimmer to it. If you followed my directions, and it doesn't look great, then this product will not work for you. If it looks and feels great, let's continue. This next part is agonizingly slow and painstakingly detailed, but it's all in the prep work.

1) Order sealer up to double the manufacturer's specifications. They state 400^2ft per gallon, but I needed one gallon per 200 square feet. However, everything plays into quantity and dry time: temperature, humidity, porosity, material, etc.
2) Order the Chapin International 61500 Backpack Sprayer for Fertilizer, and assemble it. Also order an extra-large wide mouth funnel.
3) Prepare the paver surface:
3a) Use weed killer to neutralize plant life on/in/around/between pavers. Wait 24-48 hours.
3b) With a jet nozzle hose attachment, use your garden hose to spray the crevices between your pavers in order to "dig out" sand and soil. Use a combination of the jet nozzle and a stiff-bristle shop brush to clean your pavers. If necessary, use a single dot of dishwashing liquid on oily spots but don't expect much. Consider it your stones' character, and the sealer will cover some of that.
3c) Allow 48 hours' dry time in full sun with low humidity. Just because you can't see surface water, doesn't mean all the water has evaporated from the paver and crevices!
3d) Feel the paver surface. If you feel surface grit, dust, or sand, repeat 3b and 3c and potentially use a leaf blower to assist you.
3e) Once the paver surface has been dry for 48 hours and is 100% free of grit, dust, and sand, it's time to sand between the pavers. I used "fine" grade playground sand. I would not use polymeric sand because the sealer is going to seal the sand in place anyway. Pour a 50-pound sack of sand onto the pavers, and use the shop brush to push the sand into the paver crevices. When you have sand roughly level with the paver surface, use the "mist" or "shower" setting on your garden hose nozzle and wet the pavers and sand. Your goal is to get the sand in the crevices sopping wet - and to stop just the second before it starts to run! Again, do not let the water run because it will carry away the sand with it. The hope is that the moisture will drag the sand further into the crevices. The proper depth for sand is 1/8" to 1/4" below the paver surface.
3f) Wait 24 hours and repeat 3e. Wait 24 hours to dry.
3g) Now for the fun part. Use a shop brush and a leaf blower to remove every microscopic grain of sand from the pavers' surfaces. It will feel impossible. Every time you use the brush or blower, you're carrying away sand from the crevices. It's awful. You'll question your life choices. Eventually it works, and you'll wipe a paver with your fingers and it will be free of dust and grit, and you'll believe that one day your life will return to normal. Now use 4" painter's tape around any vertical or horizontal surface that you don't want covered with sealer.
4) When you have a 4-day stretch of sunny weather with no humidity or wind and temperatures between 70 and 85 degrees, it's time. Ensure the lid of the 5-gallon sealer is tightly affixed, and begin shaking the sealer container vigorously. Turn it upside down and do the same. You want to vigorously shake for up to 5 minutes.
5) Pour 4 gallons of the sealer into the Chapin International 61500 Backpack Sprayer using the extra-large wide mouth funnel you ordered. Replace the lid on the sealer container.
6) Begin spraying, leaving yourself an exit strategy. Hold the wand close to the surface - inches, even - and make small circles. Your goal is to wet the material but stop JUST A NANOSECOND before it begins to run. Again, a dot, sprinkle, or splatter of material is fine, but a run is not, and a pool definitely isn't. It will look like the sand in the crevices isn't being covered, but it is so ignore the tendency to overspray. When you're done with one coat, clean the Backpack Sprayer per the manufacturer's instructions and wait.
7) In 24 hours, repeat Step 6 for a second coat. Spray just as heavily as you did the first time, but do NOT let this sealer pool or form rivers! You will notice this second coat appears to sit like milk for much longer than last time. Good. When you're done with this second coat, clean the Backpack Sprayer per the manufacturer's instructions and wait.
8) You will notice what looks like little tiny dots of milk sitting in the small cracks or indentations of pavers. Ignore these, as they will disappear as the sealer dries.
9) Hopefully, you timed the weather appropriately and you have a nice, long stretch of weather with very low humidity and sunny weather in the low 80s for about a week. In 48 hours you'll be able to walk on your pavers, and in a week or two you can drive on them.

This seems like more work that it's worth, but it isn't. Again, the look of these pavers is just showroom quality and glossy and beautiful. I'm so glad I did this, but if you're not comfortable with timing the weather, and a huge amount of prep work, you may want to leave this to a professional.

7. Glaze ‘N Seal Color Enhancer Paver Sealer, 1 Gallon (923)

Glaze

  • Superior Enhanced Look
  • Oil and Grease Resistant
  • Resists Color Fading
  • Deeper Color
  • Lasts Longer

Reviews from Real Users

travelrv

This product worked as advertised. Highly recommend it.

j.b.

Worked amazing. Amazing glossy finish and protection

joann scott

Easy to use and looks great

8. 5 GAL Armor AR500 High Gloss Solvent Based Acrylic Concrete Sealer and Paver Sealer

5 GAL Armor AR500 High Gloss Solvent Based Acrylic Concrete Sealer and Paver Sealer

  • Penetrating high solids, breathable solvent based acrylic coating with unmatched bonding characteristics.
  • Durable, long lasting. Stands up to abrasion, UV rays, hot tire pick up, hot and cold temperatures.
  • Long lasting high gloss finish provides up to 2-5 years of life on a two coat application before the need for a recoat. Will bring out color in dull and faded surfaces.
  • Can be used on poured concrete, stamped concrete, concrete pavers, aggregate, and more.
  • Can be used on unsealed surfaces, or on surfaces previously sealed with a solvent based acrylic.

Reviews from Real Users

NanaDeborah

My husband and I have a little over 6000 sq ft of pavers laid two years ago. They have a beautiful and natural appearance that looks good in our country setting. That said, we both like them best after a rain. We have been told the sealers can be slick, so we decided to try a single five gallon can of AR500 in a less walked area and wait for a rain before continuing. We applied two coats to our driveway earlier this week knowing rain was forecast for today. After testing it, it is true the pavers are a little slicker and the water puddles more, taking longer to dry. BUT, the shine is incredible and we just ordered 35 gallon more to finish all of our pavers.
I would be remiss if I didn't mention the chemical odor is very strong during application (fades after) and this isn't a job for sissies. My husband is a very active and strong 70 yr old farmer and did all the application himself (backpack sprayer, then roller) but it was exhausting. Nevertheless, because the pavers are SO GORGEOUS now, he's the one who made the decision to continue with the rest of the pavers.
A final note: I ordered my first five gallon thru Amazon. When the product arrived, a coupon for a small amount was offered on future purchases. When the code wouldn't work, I called Foundation Armor and their customer service was outstanding. They directed me to their web site where the coupon not only worked, but I still received free shipping and, because of the quantity I ordered, I received a quantity discount not available at Amazon.

Travel & Review

The 5 gal drum that was sent was pretty badly damaged but only leaked about a gallon or so of the material. After working with the company directly they were able to compensate me for the lost material.
Now that the issue is out of the way, let me tell you why you need to use this over an epoxy.
First off, the texture of this stuff is perfect for areas you'll have high water collection and high traffic, aka, your garage. It allows just enough of the concrete texture to come through to where you won't have issues with slipping. Also it appears to be way less maintenance than an epoxy coating (epoxy can flake off).
The best up side of this option is the price. I was quoted almost $2k for an epoxy coating on our concrete. Assuming this only lasts 5 years, I can re-apply this stuff 10x before even touching the cost of an epoxy job. I will be using this on all of our concrete areas from now on. Great stuff! I will post before and after photos after I put the last coat on the garage floor.

jmbreeze23

I spent a lot of time researching what sealer to use on my 2008 stamped patio. I paid to have it sealed a few times in the past, only to have it fade out and get a white haze on it. I was nervous about doing it myself, but after reading tons of reviews (many were helpful), I finally purchased this sealer. I was torn between this one and the AR350, but I really wanted that "wet" look, so I purchased the AR500. My patio had not been sealed for over 2 years. It had faded and looked as dry as a clay flower pot. There were black spots where the water had sat each time it rained. I spent a lot of time prepping the patio and trimming in the grooves. The ONE BIG lesson I learned was next time, I'm going to invest in a metal canister sprayer and have my fiancé back roll it after I spray. It took WAY too much time to trim in the grooves. The roller I used was 5/8". If I'd used 1", not sure that would have made a difference. Also, the other very helpful tip someone mentioned was when you pour out of the can, to have the open part closest to your hand, instead of to the pan you're pouring into. I didn't understand that at first, but it kept any sealer from dripping on the lid. The fumes are very strong, so I recommend to close your windows while using the sealer and for a day once it's drying. I wish I'd taken a picture, but the box it arrived in, made it VERY easy for me to carry. It had a hand cut out on each side - one side toward the front, the other toward the back. I was worried about how heavy it might be, but I was able to carry it to the back yard. Supplies used - small hand brush, large push broom, 9" roller with 5/8" nap with long pole, 3 or 4" paint brush and an paint tray with disposable liners. Here are the steps I did to make it successful:

1. Cleaned patio with Dawn dish soap and water. Bought a hand held brush and used a push broom with a bucket & hose. I didn't want to power wash it as I was afraid it might get damaged due to the age.

2. Used a leaf blower to get rid of excess water and let it dry for a couple days. Since it was so porous, I figured the water was still down in the concrete.

3. Started sealing - first trimmed the area I was doing with the paint brush - against the foundation and in between the grooves. Rolling it on only, it was not getting down in the grooves or against the foundation.

4. Let it dry for a few days and returned the furniture to the patio.

5. After a few weeks, it started to fade/turn white in spots. I also had some bubbles in the sealer. I was discouraged, so I messaged Foundation Armor and shared pics. They said it should be fine once I do the second coat. I probably should have used some xylene on it to remove the bubbles, but didn't.

6. About 2.5 months later (due to my schedule and weather) put on a 2nd coat with roller and didn't use the paint brush as much to trim. (I did use the hose again to rinse off any pollen, etc and let dry a few days before sealing)

7. Waited about another week, and saw a few spots that still looked lite due to the highs/lows of the patio. This time used the paint brush and touched up the patio by hand. Bubbles were still in the areas where I put it on probably a little thick. The 2nd coat and touch up coat, didn't really remove too many of them.

8. Waited a few more days and placed patio furniture back. And I'm DONE! lol

I'm very pleased with how it turned out. A stamped patio is an investment in itself, so it's important to also keep it sealed properly. I will probably put one more coat on in the Spring as I have a gallon or so left in the can. The instructions say it will keep for a year. For reference, my patio is 20' x 25' and I purchased the 5 gallon bucket.

I hope this review helps anyone who might be on the fence about purchasing this sealer. I highly recommend. The only reason I gave it 4 stars for durability and ease of use, is because I'm not sure how it will look a year from now and it was a little challenging to use the product, but well worth it!!

Good luck and you'll be happy when you're done! Enjoy the pics and a few of my doggie!

9. Quikrete High Gloss Sealer gal – 2pack

Quikrete High Gloss Sealer gal - 2pack

Reviews from Real Users

Rosco

Applied Quikrete High Gloss Sealant to my stamped colored concrete patio and to the top of my tiled built-in barbeque. Both projects came out beautifully and i am extremely happy with the product.
For the concrete, I applied the sealant with an ordinary pressure sprayer ($10 at my local hardware store) It went on easily without any problems. I did have a few area's of over spray but those wiped up with paper towels. I let that dry overnight and applied a second coat the next day. The sealant really brings out the color in the concrete and has just the right amount of that glossy "wet" look.
As for the top of my barbecue, I used a 4 inch roller brush with a medium nap, again applying 2 coats and was amazed the way the sealant brought out the colors of the tile. Again, very happy with the results.
Now we'll see how it holds up to the test of time and the elements.

markspark

I used this for 3 years on my red brick patio. The beautiful shine is gone before autumn. Super fast to roll on my 400 sq feet. Leaves a milky finish the following year after I powers wash, but disappears after I apply next years coat. I never use the stripper before hand. Patio looks great for the spring and most of summer for just two hours work.

Ron M.

I used this on my garage floor. I put two coats on a couple days apart. I applied it with a roller and a handle attached so I could do it standing up. It dried quick enough that I could put everything back inside before the end of the night. I do recommend waiting a few days before putting your vehicle back in the garage because the rubber from the tires will stick to the sealant. This really does waterproof the cement. When it rains and I bring the vehicle inside, the water puddles on the floor and I have the sweep it outside. It doesn’t get absorbed into the floor.

10. 1 Gal. DOMINATOR NG+ Clear Acrylic Sealer | No Gloss Paver Sealer | Wet Look, Color Enhancing | Professional Grade | Concrete Pavers and Decorativ

1 Gal. DOMINATOR NG+ Clear Acrylic Sealer | No Gloss Paver Sealer | Wet Look, Color Enhancing | Professional Grade | Concrete Pavers and Decorative Concrete | Fast Dry | Driveway, Patio and Walkways

  • WET LOOK, NO GLOSS: Give yourself the gift of outstanding curb appeal with the DOMINATOR NG+. It restores faded colors, gives off a low to no sheen, and improves the durability of your pavers or decorative concrete. Not intended for stone or clay pavers.
  • PROTECTS against oil stains and other spills while providing the ultimate weather resistance on surfaces including concrete pavers and decorative concrete. Not intended for stone or clay.
  • GREAT COVERAGE RATE: 250-400 square feet per gallon, per coat. You will save money and time by reducing maintenance when you seal with DOMINATOR NG+.
  • Breathe easy with DOMINATOR NG+ concrete sealer’s water-based formula. No harsh odors and low VOCs (Volatile Organic Compounds) make’s application pleasant and easy.
  • EASY spray on application using our Quick Start guide (included in every purchase) and How To videos. DOMINATOR NG+ has an incredibly fast dry time between coats (45 min.) making it an easy one-day project, unlike some competitors.

Reviews from Real Users

Kurt Brown

we wanted to follow up with this product after applying Polymeric Sand in between our patio pavers. This sealer is very effective in "locking in" the sand. It's a hard finish that will not only secure the sand, but will definitely help prevent weeds from growing which was really the whole point of the project for us. We needed 2 five gallon containers for 1100 square feet, and that did not quite give us 2 complete coats. The second coat really does help. Not sure how many years we'll get out of this but I can see where reapplying the sealer every other year might be a possibility. My wife and I worked together, she applied the sealer with an ordinary garden sprayer and I quickly flowed behind her with a paint roller to spread it out and cover evenly. That worked very well. She sprayed the cracks between the pavers where we needed it most, and the roller spreads out the excess evenly onto the paver surfaces.

Amazon Customer

I have pavers in NJ that are 2 years old. They were never sealed and looked dull and chalky. I wanted to preserve them as well as enhance the color without a high gloss look. I reviewed many paver sealer brands and Dominator NG+ Matte was always given high reviews. They let you buy a small sample to try which we used to be sure we liked it. It is not cheap but well worth it. We have a 1500 Sq ft patio and just made it with 5 gallons. 3 hours to apply sealer (not including prep of taping off house and scrubbing bird poop. We used a garden lawn sprayer from a local box store. Goes on white so you can see it and dries clear. I am hoping to get a few years of protection but will not know yet.

Dapping

I picked this product after extensive research and am very pleased with the results. The directions are clear and the product was easy to work with. It took some trial and error to get used to the sprayer, but once I got the settings right the application went quickly. As usual it seems to take more time getting the site prepped and ready to go. I added sand as needed to the pavers with care taken to remove any on the paver surfaces. I taped and papered the borders with the house and lanai frame to avoid overspray. My initial estimate of 1 gallon was totally off as I ended up using about 3 1/2 gallons over 2 coats for approx 700 sq ft. I am anxious to see how it lasts with the weather here in SW Florida

What to Consider for paver sealer

Here are the key considerations

Features You are Looking for

The product should have the features you are looking for. All the reputed marketplaces and online shops write product descriptions, read them, assess them according to your need. If you are not happy with what they wrote on there, ask them.

You know what? Ifs better to regrate before than after purchasing a product online. Returning products is a hassle.

While checking the product features, compare its pros and cons. Here in our list, we picked the {replaceKey} features from Amazon, to make a quick look. Hope that helps.

Users Feedback and Brand Recognition

Certainly, a product is available on the market for a while, the brand hit some sales and obviously, there is a customer base. If you make a few google searches and read some user feedback you will get a nice idea about that product and brand value and recognition.

The good thing is here we have compiled some good feedback from real users, I mean verified product owners.

There are a few tricks to understand a brand value and recognition like how loyal the customers are, how much visible the brand is? What is their customer support like?

Support and warranty

Sometimes the product you purchase needs customer support and that’s important. So it’s better to check their official website and support system. How faster their response is and how helpful they are.

So support depends on your product type and services. You should define the product and how consistent customer support you will be needing or not.

Product Price

Product price plays an important role in purchase decisions. Yes, some products provide real value for the money, but it does not mean high price product is always good. But you know money talks and a product with better price, chances are the product is good.

Conclusion

The customer reviews compiled above helped you to understand the pros and cons of the product. Customers review helps to take decision real quick. It saves your time and effort. So you got some idea on paver sealer, That is our happiness.

Similar Posts

Leave a Reply

Your email address will not be published.